[ESP-ENG] Un logo nuevo para mi gorra | A new logo for my cap
A big hug to everyone, I am pleased to share again with all of you in this great community that is @needleworkmonday, I wanted to make a logo to a cap that belongs to my son, he did not use it because he said it was very childish because of the logo it had, so I made a change in it for me to be able to use it, it's a little difficult to change the logos that are embroidered as in the case of my son's cap, so I used a piece of fabric to cover that part, and of course always highlighting the logo of this incredible platform like HIVE BLOG, so it was time to grab the thread and needle again. Now let's see that transformation.
- Los materiales a utilizar son:
- Una gorra a la que le quieras cambiar el logo.
- Lápiz.
- Pincel.
- Pintura roja.
- Hilo de coser.
- Aguja.
- Tijera.
- Retazo de tela.
- The materials to be used are:
- A cap that you want to change the logo on.
- Pencil.
- Paintbrush.
- Red paint.
- Sewing thread.
- Needle.
- Scissors.
- Piece of cloth.
- Paso 1: Primeramente debemos dibujar cada una de las letras de HIVE en la visera de la gorra, luego con la pintura roja procedemos a pintarlas una a una.
- Step 1: First we must draw each of the letters of HIVE on the visor of the cap, then with the red paint we proceed to paint them one by one.
- Paso 2: Luego de pintar todas las letras, dejamos secar, con el retazo de tela cubrimos el logo de la gorra y con el lápiz comenzamos a marcar las medidas para saber por donde vamos a recortar.
- Step 2: After painting all the letters, let them dry, cover the cap logo with the piece of fabric and with the pencil start marking the measurements to know where we are going to cut.
- Paso 3: Una vez medido el retazo de tela, cortamos 1 cm más de lo marcado, luego con el lápiz procedemos a dibujar el logo de nuestra increíble plataforma para luego pintarlo con la pintura roja.
- Step 3: Once the piece of fabric is measured, we cut 1 cm more than the marked, then with the pencil we proceed to draw the logo of our incredible platform and then paint it with red paint.
- Paso 4: Luego de pintar todo el logo, dejamos secar, del lado al revés de la tela doblamos 1cm y procedemos a coser por toda la orilla de la tela ya cortada.
- Step 4: After painting the entire logo, let it dry, fold 1cm on the wrong side of the fabric and proceed to sew along the edge of the fabric already cut.
- Paso 5: Una vez que ya tenemos toda la tela cosida, la colocamos sobre el logo viejo de la gorra, que cubra toda la figura anterior, y con mucho cuidado procedemos a coser por toda la orilla para que pueda quedar fijo y cubierto todo el logo.
- Step 5: Once we have all the fabric sewn, we place it over the old logo of the cap, covering all the previous figure, and carefully proceed to sew all around the edge so that it can be fixed and covered all the logo.
0
0
0.000
Congratulations @yannet80! You have completed the following achievement on the Hive blockchain and have been rewarded with new badge(s) :
Your next target is to reach 2500 upvotes.
You can view your badges on your board and compare yourself to others in the Ranking
If you no longer want to receive notifications, reply to this comment with the word
STOP
Hola @yannet80, gusto en saludarte, veo que has hecho una gran transformación con esa gorra. Que bueno que tengas la iniciativa de promover la plataforma. Te felicito.
Hola kattycrochet, para mí es un placer promover esta gran plataforma la cual me da la oportunidad de compartir con personas increíbles, gracias por tu comentario.
🤗😘