[ESP-ENG] Mi careta protectora | My protective mask
A big hug for everyone, thankful again to be able to share with you, today I will show you a protective mask in these times of pandemic, which is necessary to use both children and adults, for me it is very necessary because I work all day and interact with many people, and as they are expensive, I decided to make a mask with useful material, it should be noted that it should be used with their respective mask. Now let's see the step by step.
- Los materiales a utilizar son:
- 1 Carpeta transparente.
- Tijera.
- Lápiz.
- Foami.
- Silicón en barra.
- Cierre mágico.
- 1 Regla.
- The materials to be used are:
- 1 Transparent folder.
- Scissors.
- Pencil.
- Foami.
- Silicone stick.
- Magic clasp.
- 1 ruler.
- Paso 1: Se procede a cortar la carpeta por la mitad y a lo largo, luego a una de las 2 partes la recortamos 4cm por un lado bien sea por el lado izquierdo o derecho, y 4 cm por la parte inferior de la misma, luego en el foami se debe marcar una medida de 1cm de ancho por 35cm de largo ( si el foami es pequeño).
- Step 1: We proceed to cut the folder in half and lengthwise, then one of the 2 parts we cut 4cm on one side either on the left or right side, and 4 cm at the bottom of it, then in the foami should be marked a measure of 1cm wide by 35cm long (if the foami is small).
- Paso 2: Una vez que medimos en el foami, procedemos a recortar, hasta sacar 2 tiras, en mí caso el foami era pequeño y por eso saque 2 tiras, luego comenzamos a empatar las 2 partes de las tiras del foami, esto para que nos pueda quedar bien sujetas a la hora de colocarlas alrededor de la cabeza.
- Step 2: Once we measure in the foami, we proceed to cut, to get 2 strips, in my case the foami was small and so I took out 2 strips, then we begin to tie the 2 parts of the strips of foami, this so that we can be well secured when placing them around the head.
- Paso 3: Una vez empatadas las partes, colocamos silicón por toda la orilla del plástico y pegamos las tiras del foami, luego dibujamos en un foami de otro color cualquier diseño que usted prefiera, puede ser, una flor, una corazón, una estrella, en mí caso dibuje un corazón.
- Step 3: Once the parts are tied together, we place silicone all around the edge of the plastic and glue the foami strips, then we draw on a different color foami any design you prefer, it can be a flower, a heart, a star, in my case I drew a heart.
- Paso 4: Luego recortamos el corazón y lo pegamos a la tira de foami que le colocamos al plástico, yo lo coloqué en la parte donde se empató la tira del foami para disimular dicho empate, y para darle un adorno a mi careta, luego agarramos el pedazo de cierre mágico y lo despegamos.
- Step 4: Then we cut out the heart and glue it to the foami strip that we placed on the plastic, I placed it in the part where the foami strip was tied to hide the tie, and to give an ornament to my mask, then we grabbed the piece of magic zipper and peeled it off.
- Paso 5: Por último pegamos por la parte al revés un pedazo de cierre mágico en uno de las extremos de la tira del foami, y la otra parte del cierre mágico lo pegamos en el otro extremo de la tira pero por el lado derecho, esto es, para sujetar bien la careta y ajustar a nuestra medida.
- Step 5: Finally we glue a piece of magic zipper on one of the ends of the foami strip, and the other part of the magic zipper we glue on the other end of the strip but on the right side, that is, to hold the mask well and adjust it to our size.
0
0
0.000
Congratulations, your post has been upvoted by @dsc-r2cornell, which is the curating account for @R2cornell's Discord Community.
Thank you very much.