Reparación de las manillas de las puertas de mi carro // Repair of my car door handles

avatar

EN ESPAÑOL:

Hola amigos, hoy quise dedicarle gran parte del día al arreglo de algunos detalles de las manillas de las puertas de mi carro, ya que el asa de estas manillas se fueron partiendo, la verdad es que esta situación es incomoda, porque hay que abrir la puerta por fuera, les cuento que mi esposa sufre cuando conduce el carro y tiene que abrir la puerta, aunque cuando anda de copiloto yo le abro la puerta como todo un caballero, bueno gracias a las manillas, jaja....

IN ENGLISH:

Hello friends, today I wanted to dedicate a large part of the day to fixing some details of the door handles of my car, since these handles were breaking off, the truth is that this situation is uncomfortable, because you have to open the door from the outside I tell you that my wife suffers when she drives the car and has to open the door, although when she is the co-pilot I open the door for her like a gentleman, well thanks to the handles, haha....

Bueno amigos, mi carro es un Kia Optima, la verdad es que a la mayoría de estos carros se les parten las manillas de las puertas, el problema es que el asa es muy delgada, lo cual las hace muy débil. he visto que por mercado libre que las venden de aluminio, pienso que con este material de aluminio deben ser màs resistentes pero son muy costosas y por ahora no las puedo comprar, así que decidi reparar estas manillas.

Well friends, my car is a Kia Optima, the truth is that most of these cars have the door handles break, the problem is that the handle is very thin, which makes them very weak. I have seen that on the free market they sell them in aluminum, I think that with this aluminum material they should be more resistant but they are very expensive and for now I cannot buy them, so I decided to repair these handles.

image.png

Reparación de las manillas de las puertas de mi carro // Repair of my car door handles

Bueno amigos, hoy decidí reparar las manillas de las puertas de mi carro, lo importante es que todos los pedazos de estas manillas las había guardado, yo siempre he dicho que no podemos decir que algo es dificil de hacer sin antes intentarlo, con intentarlo no se pierde nada.

Well friends, today I decided to repair the door handles of my car, the important thing is that I had saved all the pieces that had broken, I have always said that we cannot say that something is difficult to do without first trying it, trying it yes. not working. nothing is lost.

Miren el estado de las manillas de las puertas de mi carro: / Look at the condition of my car's door handles:

image.png

Esta manilla es del lado del copiloto, pero asi mismo estan dañadas la manilla del lado del chofer y la de una puerta trasera. / .That handle is on the passenger side, but the driver's side handle and a rear door handle are also damaged.

Desmontaje de las manillas para proceder a repararlas: / Disassembly of the handles to proceed with repair:

Para retirar las manillas de las puertas es necesario remover toda la tapicería de la puerta.

To remove the door handles it is necessary to remove all the door upholstery.

image.png

Voy a comenzar con la reparación: / I'm going to start with the repair:

Bueno amigos, la reparación consiste en unir el asa que se partió con el resto de la manilla, la idea es unir estas dos partes, pero que dicha unión quede bastante resistente, para ello voy a utilizar un pegamento EPOXI de uso industrial este pegamento me lo regaló mi sobrina el año pasado y aun me queda algo guardado, tambien voy a reforzar la unión de las piezas con alambre, la idea es que la unión de las piezas queden fuertes para que no se vuelvan a romper.

Well friends, the repair consists of joining the handle that was broken with the rest of the piece, the idea is to join these two parts, but that said union is quite resistant, for this I am going to use an EPOXY glue for industrial use, this glue It will help me. My niece gave it as a gift last year and I still have some left. I am also going to reinforce the union of the pieces with wire, the idea is that the union of the pieces is strong so that they do not break again.

image.png

Lo primero es realizar unas marcas profundas en ambas piezas: / The first thing is to make some deep marks on both pieces:

Con un alambre caliente voy a realizar algunas perforaciones superficiales a cada pieza para que el pegamento de pueda adherir, también haré unos orificios a ambas piezas para insertar los alambres y el lijado.

With a hot wire I am going to make some superficial perforations in each piece so that the glue can adhere, I will also make some holes in both pieces to insert the wires and sandpaper.

image.png

Voy a colocar los alambres de refuerzo: / I am going to place the reinforcing wires:

image.png

A continuación voy a juntar las dos piezas en su posición correcta, luego con un alambre caliente voy fundir levemente la ranura con la idea de que estas dos piezas se unan y no se muevan y así poder aplicar el pegamento EPOXI:

Next I am going to join the two pieces in their correct position, then with a hot wire I am going to slightly melt the slot with the idea that these two pieces join together and do not move and thus be able to apply the EPOXY glue:

image.png

Lo siguente será la aplicación del pegamento EPOXI / Next will be the application of the EPOXI glue

Preparando la mezcla EPOXI: (producto base y la resina) /Preparing the EPOXY mixture: (base product and resin)

image.png

Aplicación del pegamento: / Glue Application:

image.png

Ahora voy a esperar a que se seque el pegamento y luego comenzaré a darle su respectivo acabado para eliminar la marca de la unión:

Now I am going to wait for the glue to dry and then I will begin to give it its respective finish to eliminate the mark of the union:

image.png

El acabado de la pieza. / The finish of the piece.

Bueno amigos, la manilla quedó bastante fuerte y resistente, pero me falta cubrir la marca de la unión de estas piezas, voy a intentar cubrir esta ranura con el uso de fondo de relleno automotriz para luego lijar con lija 2000

Well friends, the door handle was quite strong and resistant, but I need to cover the mark where these pieces join, I am going to try to cover this slot with automotive putty and then sand with 2000 sandpaper.

image.png

Bueno amigos, el trabajo quedó muy bien de esta misma manera repararé las demás manillas, así que valió la pena el intento, ahora voy a colocar esta manilla en la puerta del carro, lo unico que le falta es pintura, pero más luego voy a conseguir una pintura de color gris y el promotor de adherencia, cuando las pinte van a quedar mejor que las originales..

Well friends, the job went very well, I will repair the other handles in the same way, so it was worth trying, now I am going to place this handle on the car door, the only thing it needs is paint, but then I will apply a paint to it gray and the adhesion promoter, when you paint them they will look better than the originals.

Miren como quedó la manilla: / Look how the handle turned out:

image.png

Bueno amigos, me siento feliz y contento por haber reparado las manillas de las puertas de mi carro, mi esposa se sorprendió cuando las vió instaladas en el carro, la verda es que quedaron muy bien, solo le falta aplicarle una capa de promotor de adherencia y una capa de pintura y listo. ¿QUE LES PARECIÓ ESTA REPARACIÓN?

Well friends, I feel happy and content for having repaired the door handles of my car, my wife was surprised when she saw them installed in the car, the truth is that they turned out very well, they just need to apply a layer of adhesion promoter and a coat of paint and that's it. WHAT DID YOU THINK OF THIS REPAIR?



0
0
0.000
6 comments
avatar

Oye amigo fue un gran trabajo el que hiciste... Te las ingeniastes

0
0
0.000
avatar

Bueno ferbu, ahorita como esta la situación economica, "hay que ingeniarselas", saludos..

0
0
0.000
avatar

Hiciste un excelente trabajo con las manillas. El refuerzo metálico es necesario para que soporte la presión. Me gustaría saber el nombre del pegamento que usaste

0
0
0.000
avatar
(Edited)

Hola gpache, oye amigo este pegamento viene en cuñetes o pailas, en realidad no conozco el nombre, mi sobrina trabaja en una empresa y le regalaron un litro de los dos componentes, pero por alli salió a la venta un producto tipo plastilina que al unir los dos componente se convierte en una masa super resistente, muy similar al hierro, un amigo lo utilizó y me dice que es maravillosa para unir metales, saludos..

0
0
0.000
avatar

Hice lo mismo ya hace varios años jeje me sorprende claro que estéticamente su trabajo se ve impecable, al mio si se le ve la línea del pegamento

0
0
0.000
avatar

Hola Daniel, bueno amigo la situación nos obliga a inventar, la verdad es que la manillas quedaron fuertes, te cuento Daniel, que tenia guardadas las tres piezas que se partierón y solo aparecieron dos, ahora sino aparece esa pieza tendré que fabricarla, pero ahora se me complica la cosa, por lo menos puede arreglas dos puertas, saludos y gracias por tu comentario...

0
0
0.000